Closed Traverse
A closed traverse is a series of connected lines whose lengths and bearings are measured off these lines (or sides), which enclose an area. A closed traverse can be used to show the shape of the perimeter of a fire or burn area. If you were to pace continuously along the sides of a closed traverse, the finishing point would be the same as the starting location.
Note in the following sketch how the traverse is followed clockwise. If the direction was followed counterclockwise at any point, the bearing letters would change to their opposites but the numbers would not, as shown in the first sketch (1) below. The second sketch (2) is a closed traverse. Here, the series of lines completes a distance area, and the starting and ending points are the same.
Example 1  Jeff paced the perimeter of the Zavala fire. His pace is 13 paces/chain. The declination for his current location is 14.5°E. The direction, distance, and travel for Jeff is as follows: Jeff begins at point 1 and goes N42°W for 27 paces; from point 2 he goes N75°W for 161/2 paces; from point 3 he goes N31°W for 241/2 paces; from point 4 he goes N36°E for 291/2 paces; from point 5 he goes S65°E for 22 paces; from point 6 he goes S13°E for 521/2 paces; from point 7 he goes S21°W for 101/4 paces back to the starting point, point 1.
Convert the bearings to magnetic readings. Adjust the magnetic readings to true north readings. Plot the closed traverse in feet using an engineer's tenth ruler and protractor.
Step 1. Convert paces into feet. Jeff's pace is 13 paces per chain. Set up the cancellation table (Section 2.1) and solve for distance in feet.
Repeat this step for each distance.
Step 2. Convert the bearings to magnetic readings. See Section 6.1.
The NW quadrant is between 270° and 360°. 360°  42° = 318°
The SE quadrant is between 90° and 180°. 180°  65° = 115°
The NE quadrant is between 0° and 90° so those values are used as recorded.
The SW quadrant is between 180° and 270°. 180° + 21° = 201°
The resulting magnetic reading are listed in the table below.
Step 3. Adjust each magnetic reading to a true reading following the guidelines in Section 6.5.
Step 4. Choose a scale. 1/10 inch = 10 feet
Step 5. Using a protractor (angles measured in degrees) and an engineer's scale or tenth's ruler, plot the plan view of the traverse horizontal distance (feet) and the bearing (degrees) between points.
Step 5a. Set the protractor so the 0°/180°line is up (north) and on a northsouth axis.
Step 5b. Put a point in the middle hole. This will be point 1.
Step 5c. Read 318° on the outer scale of the protractor. Put a dot to mark the point.
Step 5d. Draw a line from point 1 up to the dot that is 137/10 marks (each inch has 10 marks).
Step 5e. The end of this line will be point 2. Put the hole of the protractor on point 2. Follow steps 5b and 5c with each of the values.
When plotting the values that are in the southern quadrants with a semicircle protractor, rotate the protractor so the 0°/180°line is down (facing south) and read the numbers on the inner scale. Continue to complete all the points. The end result should be a closed traverse as shown.
Step 5f. Convert the true readings to bearings.
P1 to P2 = 360°  332.5° = N27.5°W
P2 to P3 = 360°  299.5° = N60.5°W
P3 to P4 = 360°  343.5° = N16.5°W
P4 to P5 = 0° + 50.5° = N50.5°E
P5 to P6 = 180°  129.5° = S50.5°E
P6 to P7 = 181.5°  180° = S1.5°E
P7 to P1 = 215.5°  180° = S35.5°W
Label the lines of the traverse with the corresponding bearings.
